Home | |
VAN SEATS | |
Captain Chairs | |
Qualitex Zenith High Back Van Seat

Qualitex Zenith High Back Van Seat

AVAILABLE IN TWO-TONE	REAR POCKET
GENTLE BOLSTERING	ADJUSTABLE HEADRESTS

Starting at $396.90
List Price $661.50 (40% Savings)

Material *: Fabric
Vinyl
Leather +$120.00
Seat Option: Seat Heater +$105.00

This outstanding seat heater will provide warm, soothing comfort on the road while also helping to reduce lower back stress. Feel the difference within one minute! The unit comes with a three-position switch and consistent temperature monitoring to prevent overheating.

▪ Separate temperature sensors for the back and bottom, to provide even heating.

119003
Seat Massage +$145.00

Pamper yourself with this luxurious seat massage system. Four inflatable bladders are powered by a pneumatic motor for a one-of-a-kind driving experience. Experience full relief from back fatigue and feel refreshed after a long journey. Great for use with the seat heater, for the ultimate in ergonomic sustenance.
▪3 year/36,000 mile warranty.

119004

Manual Lumbar Support +$75.00

An inflatable bladder installed within the seat will give your back muscles all the support they need. Use the attached bulb to adjust the bladder to any preference. Great for combined use with the Rostra seat heater, for the ultimate in ergonomic sustenance.
119001

Power Lumber Support +$145.00

An inflatable bladder installed within the seat will give your back muscles all the support they need. At the touch of a control button which is directly attached to the seat, you can adjust the bladder to any desired preference. Great for combined use with the seat heater, for the ultimate in high-tech ergonomic performance.
▪ Ergonomic control switch
▪ Sound dampening patch to minimize noise
▪ Adjustable seat bladder

119002

6 Way Power Base +$320.00

Enjoy maximum individualized comfort with this seat base, which will allow your chair to support your frame in six different positions. Three convenient access buttons allow for up/down, forward/back and tilting motions. Customize your favored seating position, or change it as needed.

110995

7 Spring Seat Frame Bottom +$75.00

The seven springs in this seat frame bottom will provide a solid, firm support base when needed, which also helps to increase seat longevity. Recommended for passengers over 200 lbs.
119010
Flexsteel Base Handle +$9.00

This accessory replaces the cable included in swivel bases, so that you can attach your new barrel chair to your existing Flexsteel swivel base.

119010
Fabric *: [V11]Encore Sandstone V11
[V3]Encore Burgundy V3
[V4]Encore Silver V4
[V44]Encore Charcoal V44
[SV5]Encore Ocean SV5
[V6]Encore Black V6
[RL1]Regal Sandstone RL1
[RL2]Regal Walnut RL2
[RL3]Regal Brick RL3
[RL4]Regal Silver RL4
[RL5]Regal Ocean RL5
[T311]Scottsdale Walnut T311
[P775]Scottsdale Sandstone P775
[Y880]Scottsdale Silver Y880
[X161]Scottsdale Charcoal X161
[R721]Scottsdale Ocean R721
[P667]Scottsdale Black P667
Vinyl *: [V121]Medium Neutral V121
[V101]Sandalwood V101
[V303]Garnet V303
[V555]Adriatic Blue V555
[V575]Midnight Blue V575
[V202]Moondust V202
[V404]Charcoal V404
[V606]Black V606
[V110]White V110
Leather *: [L121]Medium Neutral L121
[L101]Sandalwood L101
[L303]Garnet L303
[L555]Adriatic Blue L555
[L575]Midnight Blue L575
[202]Moondust L202
[L404]Charcoal L404
[L606]Black L606
[L110]White L110
Do you need a base? Let us help you. * What position will this seat be installed to?
Do you need a base? Let us help you. * In some cases, depending on your year make and model, it will require for you to use an adapter bracket or base in order to install this seat. Please go through the applications to ensure the right fit for your vehicle.
Van Rear Bases *: Fixed Van Base 5" +$99.00
5" HIGH UNIVERSAL FIXED BASE

This 5" high universal fixed base was designed to fit your aftermarket seat to your van with a 16x16" top plate size.

▪16" x 16" top plate size
▪Not predrilled
▪Seat bases tested and certified to meet FMVSS #207 safety standards per sections S4.2 and S4.3
110205
Fixed Van Base 6" +$99.00

6" HIGH UNIVERSAL FIXED BASE

This 6" high universal fixed base was designed to fit your aftermarket seat to your van with a 16x16" top plate size.

▪16" x 16" top plate size
▪Not predrilled
▪Seat bases tested and certified to meet FMVSS #207 safety standards per sections S4.2 and S4.3
110206

Fixed Van Base 7" +$99.00
7" HIGH UNIVERSAL FIXED BASE

This 7" high universal fixed base was designed to fit your aftermarket seat to your van with a 16x16" top plate size.

▪16" x 16" top plate size
▪Not predrilled
▪Seat bases tested and certified to meet FMVSS #207 safety standards per sections S4.2 and S4.3
110207
Swivel Van Base 7" +$137.00
7" HIGH CENTER BASE

This 7" high center base was designed to fit your aftermarket seat to your van with an 8x11” top bolt pattern, combined with a 7x7" hole bolt pattern that will bolt directly to the factory bolt holes on your floor, with no drilling required. Seat belt bar is included.

▪Top Bolt Pattern 8x11”
▪7" x 7" bottom bolt pattern
▪Seat belt bar
▪Seat bases tested and certified to meet FMVSS #207 safety standards per sections S4.2 and S4.3
110070
Swivel Van Base 10" +$137.00
10" HIGH CENTER BASE

This 10" high center base was designed to fit your aftermarket seat to your van with an 8x11” top bolt pattern, combined with a 7x7" hole bolt pattern that will bolt directly to the factory bolt holes on your floor, with no drilling required. Seat belt bar is included.

▪Top Bolt Pattern 8x11”
▪7" x 7" bottom bolt pattern
▪Seat belt bar
▪Seat bases tested and certified to meet FMVSS #207 safety standards per sections S4.2 and S4.3
110100
Select Year *
Bases Or Brackets Available * These are the bases or brackets available for your Chevy - GMC Full Size Van.: Your vehicle will not require additional brackets or base.
Your vehicle will not require additional brackets or a base, thanks to the universal plate included with this seat. This universal plate features set bolt patterns which will match the y

Your vehicle will not require additional brackets or a base, thanks to the universal plate included with this seat. This universal plate features set bolt patterns which will match the year, make, and model of your vehicle. Additionally, this base was manufactured to be drilled, if additional bolt holes are necessary. A standard 8x11" bolt pattern is also included.

No Thank You
1971-77 GMC-CHEVY DRIVER SWIVEL BASE

Use this base to provide a swivel option for your aftermarket seat. +$169.00

Use this base to provide a swivel option for your aftermarket seat.">
1971-77 GMC-CHEVY SWIVEL BASE

This 1971-77 GMC-Chevy swivel base was designed to fit your aftermarket seat to your van with an 8x11” top bolt pattern, combined with a stock GMC-Chevy bottom hole bolt pattern that will bolt directly to the factory bolt holes on your floor, with no drilling required.
▪Top Bolt Pattern 8x11”
▪Stock GM bottom bolt pattern
▪6” high at center
▪Seat bases tested and certified to meet FMVSS #207 safety standards per sections S4.2 and S4.3
111619
1971-77 GMC-CHEVY PASSENGER SWIVEL BASE

Use this base to provide a swivel option for your aftermarket seat. +$169.00

Use this base to provide a swivel option for your aftermarket seat.">
1971-77 GMC-CHEVY SWIVEL BASE

This 1971-77 GMC-Chevy swivel base was designed to fit your aftermarket seat to your van with an 8x11” top bolt pattern, combined with a stock GMC-Chevy bottom hole bolt pattern that will bolt directly to the factory bolt holes on your floor, with no drilling required. For passenger seats.
▪Top Bolt Pattern 8x11”
▪Stock GM bottom bolt pattern
▪6” high at center
▪Seat bases tested and certified to meet FMVSS #207 safety standards per sections S4.2 and S4.3

111620
1971-95 GMC-CHEVY DRIVER POWER BASE RISER

This riser is necessary when ordering a power base. +$124.00

This riser is necessary when ordering a power base.">
1971-95 GMC-CHEVY POWER BASE RISER

The 1971-95 GMC-Chevy power base riser was designed to match a power base to the original height of your seat.   This power base riser features a universal bottom hole bolt pattern that will bolt directly to the factory bolt holes on your floor, with no drilling required.

▪Raises the power unit to match the original seat height
▪Universal bottom hole bolt pattern
▪Seat base risers tested and certified to meet FMVSS #207 safety standards per sections S4.2 and S4.3

111071
1971-95 GMC-CHEVY PASSENGER POWER BASE RISER

This riser is necessary when ordering a power base. +$124.00

This riser is necessary when ordering a power base.">
1971-95 GMC-CHEVY POWER BASE RISER

The 1971-95 GMC-Chevy power base riser was designed to match a power base to the original height of your seat.   This power base riser features a universal bottom hole bolt pattern that will bolt directly to the factory bolt holes on your floor, with no drilling required. For passenger seats.

▪Raises the power unit to match the original seat height
▪Universal bottom hole bolt pattern
▪Seat base risers tested and certified to meet FMVSS #207 safety standards per sections S4.2 and S4.3
111072
1978-95 GMC-CHEVY DRIVER SWIVEL BASE

Use this base to provide a convenient swivel option for this van seat. +$169.00

Use this base to provide a convenient swivel option for this van seat.">
1978-95 GMC-CHEVY SWIVEL BASE

This 1978-95 GMC-Chevy swivel base was designed to fit your aftermarket seat to your van with an 8x11” top bolt pattern, combined with a stock GMC-Chevy bottom hole bolt pattern that will bolt directly to the factory bolt holes on your floor, with no drilling required.

▪Top Bolt Pattern 8x11”
▪Stock GM bottom bolt pattern
▪6” high at center
▪Seat bases tested and certified to meet FMVSS #207 safety standards per sections S4.2 and S4.3

111623
1978-95 GMC-CHEVY PASSENGER SWIVEL BASE

Use this base to provide a convenient swivel option for this van seat. +$169.00

Use this base to provide a convenient swivel option for this van seat.">
1978-95 GMC-CHEVY SWIVEL BASE

This 1978-95 GMC-Chevy swivel base was designed to fit your aftermarket seat to your van with an 8x11” top bolt pattern, combined with a stock GMC-Chevy bottom hole bolt pattern that will bolt directly to the factory bolt holes on your floor, with no drilling required. For passenger seats.
▪Top Bolt Pattern 8x11”
▪Stock GM bottom bolt pattern
▪6” high at center
▪Seat bases tested and certified to meet FMVSS #207 safety standards per sections S4.2 and S4.3

111624
1996+ GMC-CHEVY DRIVER AFTERMARKET ADAPTER

This adapter bracket is recommended to install this seat to your van base. +$64.00

This adapter bracket is recommended to install this seat to your van base.">
1996+ GMC-CHEVY AFTERMARKET ADAPTER
The 1996+ GMC-Chevy aftermarket adapter was designed to adapt an aftermarket seat to the factory base of your van. It features an 8x11” inside bolt pattern, a stock GMC-Chevy outside bolt pattern, and an attachment for the seat belt of your chair.

▪For adapting an after-market seat to a factory base
▪Seat belt attachment
▪Inside bolt pattern 8x11”
▪Outside bolt pattern 14 1/4" x 13 1/4”

111612
1996+ GMC-CHEVY PASSENGER AFTERMARKET ADAPTER

This adapter bracket is recommended to install this seat to your van base. +$64.00

This adapter bracket is recommended to install this seat to your van base.">
1996+ GMC-CHEVY AFTERMARKET ADAPTER

The 1996+ GMC-Chevy aftermarket adapter was designed to adapt an aftermarket seat to the factory base of your van. It features an 8x11” inside bolt pattern, a stock GMC-Chevy outside bolt pattern, and an attachment for the seat belt of your chair.   For passenger seats.

▪For adapting an after-market seat to a factory base
▪Seat belt attachment
▪Inside bolt pattern 8x11”
▪Outside bolt pattern 14 1/4" x 13 1/4”

111613
1996+ GMC-CHEVY DRIVER SWIVEL PLATE

Use this plate to provide a swivel option for this van seat. +$199.00

Use this plate to provide a swivel option for this van seat.">
1996+ SWIVEL PLATE

The 96+ GMC-Chevy swivel plate was designed to adapt your aftermarket seat to the factory base of your van. It features 14 ¼ x 13 ¼” top and bottom bolt patterns, and will attach easily with no drilling required.

▪Seat raise 1 5/8”
▪Seat offset 2” facing forward, 3 1/2” facing rear
▪Top bolt pattern 14 1/4” x 13 1/4”
▪Bottom bolt pattern 14 1/4” x 13 1/4”
▪Seat bases tested and certified to meet FMVSS #207 safety standards per sections S4.2 and S4.3

111616
1996+ GMC-CHEVY PASSENGER SWIVEL PLATE

Use this plate to provide a swivel option for this van seat. +$199.00

Use this plate to provide a swivel option for this van seat.">
1996+ SWIVEL PLATE

The 96+ GMC-Chevy swivel plate was designed to adapt your aftermarket seat to the factory base of your van. It features 14 ¼ x 13 ¼” top and bottom bolt patterns, and will attach easily with no drilling required. For passenger seats.

▪Seat raise 1 5/8”
▪Seat offset 2” facing forward, 3 1/2” facing rear
▪Top bolt pattern 14 1/4” x 13 1/4”
▪Bottom bolt pattern 14 1/4” x 13 1/4”
▪Seat bases tested and certified to meet FMVSS #207 safety standards per sections S4.2 and S4.3

111617
1996+ GMC-CHEVY DRIVER POWER BASE RISER

This riser base is necessary when ordering a power base for your van. +$124.00

This riser base is necessary when ordering a power base for your van.">
1996+ GMC-CHEVY POWER BASE RISER

The 1996+ GMC-Chevy power base riser was designed to match a power base to the original height of your seat.   This power base riser features a universal bottom hole bolt pattern that will bolt directly to the factory bolt holes on your floor, with no drilling required.

▪Raises the power unit to match the original seat height
▪Universal bottom hole bolt pattern
▪Seat base risers tested and certified to meet FMVSS #207 safety standards per sections S4.2 and S4.3

111618
1996+ GMC-CHEVY PASSENGER POWER BASE RISER

This riser base is necessary when ordering a power base for your van. +$124.00

This riser base is necessary when ordering a power base for your van.">
1996+ GMC-CHEVY POWER BASE RISER

The 1996+ GMC-Chevy power base riser was designed to match a power base to the original height of your seat.   This power base riser features a universal bottom hole bolt pattern that will bolt directly to the factory bolt holes on your floor, with no drilling required. For passenger seats.

▪Raises the power unit to match the original seat height
▪Universal bottom hole bolt pattern
▪Seat base risers tested and certified to meet FMVSS #207 safety standards per sections S4.2 and S4.3

111618
Select Full Size Ford Van *
Ford Bases Available *: Your vehicle will not require additional brackets or base.
Your vehicle will not require additional brackets or a base, thanks to the universal plate included with this seat. This universal plate features set bolt patterns which will match the y

Your vehicle will not require additional brackets or a base, thanks to the universal plate included with this seat. This universal plate features set bolt patterns which will match the year, make, and model of your vehicle. Additionally, this base was manufactured to be drilled, if additional bolt holes are necessary. A standard 8x11" bolt pattern is also included.

No thank you
1969-74 FORD DRIVER SWIVEL BASE

Use this base to provide a convenient swivel option for this van seat. +$169.00

Use this base to provide a convenient swivel option for this van seat.">
69-74 FORD SWIVEL BASE

This 1969-74 Ford swivel base was designed to fit your aftermarket seat to your van with an 8x11” top bolt pattern, combined with a stock Ford bottom hole bolt pattern that will bolt directly to the factory bolt holes on your floor, with no drilling required.

▪8X11” top bolt pattern
▪Stock Ford bottom hole bolt pattern
▪6” high at center
▪Seat bases tested and certified to meet FMVSS #207 safety standards per sections S4.2 and S4.3

113621
1969-74 FORD PASSENGER SWIVEL BASE

Use this base to provide a convenient swivel option for this van seat. +$169.00

Use this base to provide a convenient swivel option for this van seat.">
69-74 FORD SWIVEL BASE

This 1969-74 Ford swivel base was designed to fit your aftermarket seat to your van with an 8x11” top bolt pattern, combined with a stock Ford bottom hole bolt pattern that will bolt directly to the factory bolt holes on your floor, with no drilling required. For passenger seats.

▪8X11” top bolt pattern
▪Stock Ford bottom hole bolt pattern
▪6” high at center
▪Seat bases tested and certified to meet FMVSS #207 safety standards per sections S4.2 and S4.3
113622
1975-91 FORD DRIVER SWIVEL BASE

Use this base to provide a convenient swivel option for this van seat. +$169.00

Use this base to provide a convenient swivel option for this van seat.">
76-91 FORD SWIVEL BASE

This 1976-91 Ford swivel base was designed to fit your aftermarket seat to your van with an 8x11” top bolt pattern, combined with a stock Ford bottom hole bolt pattern that will bolt directly to the factory bolt holes on your floor, with no drilling required.

▪8X11” top bolt pattern
▪Stock Ford bottom hole bolt pattern
▪6” high at center
▪Seat bases tested and certified to meet FMVSS #207 safety standards per sections S4.2 and S4.3

113640
1975-91 FORD PASSENGER SWIVEL BASE

Use this base to provide a convenient swivel option for this van seat. +$169.00

Use this base to provide a convenient swivel option for this van seat.">
76-91 FORD SWIVEL BASE

This 1976-91 Ford swivel base was designed to fit your aftermarket seat to your van with an 8x11” top bolt pattern, combined with a stock Ford bottom hole bolt pattern that will bolt directly to the factory bolt holes on your floor, with no drilling required.   For passenger seats.

▪8X11” top bolt pattern
▪Stock Ford bottom hole bolt pattern
▪6” high at center
▪Seat bases tested and certified to meet FMVSS #207 safety standards per sections S4.2 and S4.3

113641
1992-95 FORD DRIVER SWIVEL BASE

Use this base to provide a convenient swivel option for this van seat. +$169.00

Use this base to provide a convenient swivel option for this van seat.">
92-95 FORD SWIVEL BASE

This 1992-95 Ford swivel base was designed to fit your aftermarket seat to your van with an 8x11” top bolt pattern, combined with a stock Ford bottom hole bolt pattern that will bolt directly to the factory bolt holes on your floor, with no drilling required.

▪8X11” top bolt pattern
▪Stock Ford bottom hole bolt pattern
▪6” high at center

113642
1992-95 FORD PASSENGER SWIVEL BASE

Use this base to provide a convenient swivel option for this van seat. +$169.00

Use this base to provide a convenient swivel option for this van seat.">
92-95 FORD SWIVEL BASE

This 1992-95 Ford swivel base was designed to fit your aftermarket seat to your van with an 8x11” top bolt pattern, combined with a stock Ford bottom hole bolt pattern that will bolt directly to the factory bolt holes on your floor, with no drilling required.   For passenger seats.

▪8X11” top bolt pattern
▪Stock Ford bottom hole bolt pattern
▪6” high at center

113643
1996-06 FORD DRIVER FIXED BASE

This base will easily install this seat to your van. +$199.00

This base will easily install this seat to your van.">
96-06 FORD FIXED BASE

This 1996-2006 Ford fixed base was designed to fit your aftermarket seat to your van with an 8x11” top bolt pattern, combined with a stock Ford bottom hole bolt pattern that will bolt directly to the factory bolt holes on your floor, with no drilling required. This model comes with a pyro seat belt attachment, with which you can easily attach the seat belt of your seat.

▪8X11” top bolt pattern
▪Stock Ford bottom hole bolt pattern
▪Pyro seat belt attachment
▪Raised bottom plate w/driver
▪Seat bases tested and certified to meet FMVSS #207 safety standards per sections S4.2 and S4.3

113619
1996-06 FORD PASSENGER FIXED BASE

This base will easily install this seat to your van. +$179.00

This base will easily install this seat to your van.">
96-06 FORD FIXED BASE

This 1996-2006 Ford fixed base was designed to fit your aftermarket seat to your van with an 8x11” top bolt pattern, combined with a stock Ford bottom hole bolt pattern that will bolt directly to the factory bolt holes on your floor, with no drilling required. This model comes with a pyro seat belt attachment, with which you can easily attach the seat belt of your seat. For passenger seats.

▪8X11” top bolt pattern
▪Stock Ford bottom hole bolt pattern
▪Pyro seat belt attachment
▪Raised bottom plate w/driver
▪Seat bases tested and certified to meet FMVSS #207 safety standards per sections S4.2 and S4.3
113620
1996-06 FORD DRIVER SWIVEL BASE

Use this base to provide a convenient swivel option for this van seat. +$229.00

Use this base to provide a convenient swivel option for this van seat.">
96-06 FORD SWIVEL BASE

This 1996-2006 Ford swivel base was designed to fit your aftermarket seat to your van with an 8x11” top bolt pattern, combined with a stock Ford bottom hole bolt pattern that will bolt directly to the factory bolt holes on your floor, with no drilling required. This model comes with a pyro seat belt attachment, with which you can easily attach the seat belt of your seat.

▪8X11” top bolt pattern
▪Stock Ford bottom hole bolt pattern
▪Pyro seat belt attachment
▪Raised bottom plate w/driver
▪Seat bases tested and certified to meet FMVSS #207 safety standards per sections S4.2 and S4.3

113530
1996-06 FORD PASSENGER SWIVEL BASE

Use this base to provide a convenient swivel option for this van seat. +$209.00

Use this base to provide a convenient swivel option for this van seat.">
96-06 FORD SWIVEL BASE

This 1996-2006 Ford swivel base was designed to fit your aftermarket seat to your van with an 8x11” top bolt pattern, combined with a stock Ford bottom hole bolt pattern that will bolt directly to the factory bolt holes on your floor, with no drilling required. This model comes with a pyro seat belt attachment, with which you can easily attach the seat belt of your seat. For passenger seats.

▪8X11” top bolt pattern
▪Stock Ford bottom hole bolt pattern
▪Pyro seat belt attachment
▪Raised bottom plate w/driver
▪Seat bases tested and certified to meet FMVSS #207 safety standards per sections S4.2 and S4.3
113531
2007+ FORD DRIVER FIXED BASE

This base will easily install this seat to your van. +$199.00

This base will easily install this seat to your van.">
2007+ FORD FIXED BASE

The 2007+ Ford fixed base was designed to fit your aftermarket seat to your van with an 8x11” top bolt pattern, combined with a stock Ford bottom hole bolt pattern that will bolt directly to the factory bolt holes on your floor, with no drilling required. This model comes with a pyro seat belt attachment, with which you can easily attach the seat belt of your seat.

▪8 x 11" top bolt pattern.

▪Stock Ford bottom hole bolt pattern

▪Pyro seat belt attachment

▪Driver and passenger on raised bottom plate
▪Seat bases tested and certified to meet FMVSS #207 safety standards per sections S4.2 and S4.3

113019

2007+ FORD PASSENGER FIXED BASE

This base will easily install this seat to your van. +$199.00

This base will easily install this seat to your van.">
2007+ FORD FIXED BASE

The 2007+ Ford fixed base was designed to fit your aftermarket seat to your van with an 8x11” top bolt pattern, combined with a stock Ford bottom hole bolt pattern that will bolt directly to the factory bolt holes on your floor, with no drilling required. This model comes with a pyro seat belt attachment, with which you can easily attach the seat belt of your seat. For passenger seats.

▪8 x 11" top bolt pattern.
▪Stock Ford bottom hole bolt pattern
▪Pyro seat belt attachment
▪Driver and passenger on raised bottom plate
▪Seat bases tested and certified to meet FMVSS #207 safety standards per sections S4.2 and S4.3

113022
2007+ FORD DRIVER SWIVEL BASE

Use this base to provide a convenient swivel option for this van seat. +$229.00

Use this base to provide a convenient swivel option for this van seat.">
2007+ FORD SWIVEL BASE

The 2007+ Ford swivel base was designed to fit your aftermarket seat to your van with an 8x11” top bolt pattern, combined with a stock Ford bottom hole bolt pattern that will bolt directly to the factory bolt holes on your floor, with no drilling required. This model comes with a pyro seat belt attachment, with which you can easily attach the seat belt of your seat.

▪8 x 11" top bolt pattern.
▪Stock Ford bottom hole bolt pattern
▪Pyro seat belt attachment
▪Driver and passenger on raised bottom plate
▪Approved for seats without air bags
▪Seat bases tested and certified to meet FMVSS #207 safety standards per sections S4.2 and S4.3

113530
2007+ FORD PASSENGER SWIVEL BASE

Use this base to provide a convenient swivel option for this van seat. +$229.00

Use this base to provide a convenient swivel option for this van seat.">
2007+ FORD SWIVEL BASE

The 2007+ Ford swivel base was designed to fit your aftermarket seat to your van with an 8x11” top bolt pattern, combined with a stock Ford bottom hole bolt pattern that will bolt directly to the factory bolt holes on your floor, with no drilling required. This model comes with a pyro seat belt attachment, with which you can easily attach the seat belt of your seat. For passenger seats.

▪8 x 11" top bolt pattern.
▪Stock Ford bottom hole bolt pattern
▪Pyro seat belt attachment
▪Driver and passenger on raised bottom plate
▪Approved for seats without air bags
▪Seat bases tested and certified to meet FMVSS #207 safety standards per sections S4.2 and S4.3

113532
1975-91 FORD DRIVER POWER BASE RISER

This riser base is necessary when ordering a power base for your van. +$124.00

This riser base is necessary when ordering a power base for your van.">
1975-91 FORD POWER BASE RISER

The 1975-91 Ford power base riser was designed to match a power base to the original height of your seat.   This power base riser features a stock Ford bottom hole bolt pattern that will bolt directly to the factory bolt holes on your floor, with no drilling required.

▪Raises the power unit to match the original seat height
▪Stock Ford bottom hole bolt pattern
▪5 1/2" front height, 3" rear height
▪Seat base risers tested and certified to meet FMVSS #207 safety standards per sections S4.2 and S4.3
111086
1975-91 FORD PASSENGER POWER BASE RISER

This riser base is necessary when ordering a power base for your van. +$124.00

This riser base is necessary when ordering a power base for your van.">
1975-91 FORD POWER BASE RISER

The 1975-91 Ford power base riser was designed to match a power base to the original height of your seat.   This power base riser features a stock Ford bottom hole bolt pattern that will bolt directly to the factory bolt holes on your floor, with no drilling required. For passenger seats.

▪Raises the power unit to match the original seat height
▪Stock Ford bottom hole bolt pattern
▪5 1/2" front height, 3" rear height
▪Seat base risers tested and certified to meet FMVSS #207 safety standards per sections S4.2 and S4.3

111087
1992+ FORD DRIVER POWER BASE RISER

This riser base is necessary when ordering a power base for your van. +$84.00

This riser base is necessary when ordering a power base for your van.">
1992+ FORD POWER BASE RISER

The 1992+ Ford power base riser was designed to match a power base to the original height of your seat.   This power base riser features a stock Ford bottom hole bolt pattern that will bolt directly to the factory bolt holes on your floor, with no drilling required.

▪Raises the power unit to match the original seat height
▪Stock Ford bottom hole bolt pattern
▪5 1/2" front height, 3" rear height
▪Seat base risers tested and certified to meet FMVSS #207 safety standards per sections S4.2 and S4.3

111091
1992+ FORD PASSENGER POWER BASE RISER

This riser base is necessary when ordering a power base for your van. +$84.00

This riser base is necessary when ordering a power base for your van.">
1992+ FORD POWER BASE RISER

The 1992+ Ford power base riser was designed to match a power base to the original height of your seat.   This power base riser features a stock Ford bottom hole bolt pattern that will bolt directly to the factory bolt holes on your floor, with no drilling required. For passenger seats.

▪Raises the power unit to match the original seat height
▪Stock Ford bottom hole bolt pattern
▪5 1/2" front height, 3" rear height
▪Seat base risers tested and certified to meet FMVSS #207 safety standards per sections S4.2 and S4.3

111092
Select Ram Year *
Bases Or Brackets Available *: Your vehicle will not require additional brackets or base.
Your vehicle will not require additional brackets or a base, thanks to the universal plate included with this seat. This universal plate features set bolt patterns which will match the y

Your vehicle will not require additional brackets or a base, thanks to the universal plate included with this seat. This universal plate features set bolt patterns which will match the year, make, and model of your vehicle. Additionally, this base was manufactured to be drilled, if additional bolt holes are necessary. A standard 8x11" bolt pattern is also included.

1971-77 DODGE DRIVER SWIVEL BASE

Use this base to provide a convenient swivel option for this van seat. +$169.00

Use this base to provide a convenient swivel option for this van seat.">
71-77 DODGE SWIVEL BASE

This 1971-77 Dodge swivel base was designed to fit your aftermarket seat to your van with an 8x11” top bolt pattern, combined with a stock Dodge bottom hole bolt pattern that will bolt directly to the factory bolt holes on your floor, with no drilling required.

▪Top Bolt Pattern 8x11”
▪Stock Dodge bottom bolt pattern
▪6” high at center
▪Seat bases tested and certified to meet FMVSS #207 safety standards per sections S4.2 and S4.3

112621
1971-77 DODGE PASSENGER SWIVEL BASE

Use this base to provide a convenient swivel option for this van seat. +$169.00

Use this base to provide a convenient swivel option for this van seat.">
71-77 DODGE SWIVEL BASE

This 1971-77 Dodge swivel base was designed to fit your aftermarket seat to your van with an 8x11” top bolt pattern, combined with a stock Dodge bottom hole bolt pattern that will bolt directly to the factory bolt holes on your floor, with no drilling required. For passenger seats.

▪Top Bolt Pattern 8x11”
▪Stock Dodge bottom bolt pattern
▪6” high at center
▪Seat bases tested and certified to meet FMVSS #207 safety standards per sections S4.2 and S4.3

112622
1978-93 DODGE DRIVER SWIVEL BASE

Use this base to provide a convenient swivel option for this van seat. +$169.00

Use this base to provide a convenient swivel option for this van seat.">
78-93 DODGE SWIVEL BASE

This 1978-93 Dodge swivel base was designed to fit your aftermarket seat to your van with an 8x11” top bolt pattern, combined with a stock Dodge bottom hole bolt pattern that will bolt directly to the factory bolt holes on your floor, with no drilling required.

▪Top Bolt Pattern 8x11”
▪Stock Dodge bottom bolt pattern
▪6” high at center
▪Seat bases tested and certified to meet FMVSS #207 safety standards per sections S4.2 and S4.3

112627
1978-93 DODGE PASSENGER SWIVEL BASE

Use this base to provide a convenient swivel option for this van seat. +$169.00

Use this base to provide a convenient swivel option for this van seat.">
78-93 DODGE SWIVEL BASE

This 1978-93 Dodge swivel base was designed to fit your aftermarket seat to your van with an 8x11” top bolt pattern, combined with a stock Dodge bottom hole bolt pattern that will bolt directly to the factory bolt holes on your floor, with no drilling required. For passenger seats.

▪Top Bolt Pattern 8x11”
▪Stock Dodge bottom bolt pattern
▪6” high at center
▪Seat bases tested and certified to meet FMVSS #207 safety standards per sections S4.2 and S4.3
112627
1994 DODGE DRIVER SWIVEL BASE

Use this base to provide a convenient swivel option for this van seat. +$169.00

Use this base to provide a convenient swivel option for this van seat.">
94 DODGE SWIVEL BASE

This 1994 Dodge swivel base was designed to fit your aftermarket seat to your van with an 8x11” top bolt pattern, combined with a stock Dodge bottom hole bolt pattern that will bolt directly to the factory bolt holes on your floor, with no drilling required.

▪Top Bolt Pattern 8x11”
▪Stock Dodge bottom bolt pattern
▪6” high at center
▪Seat bases tested and certified to meet FMVSS #207 safety standards per sections S4.2 and S4.3
112629
1994 DODGE PASSENGER SWIVEL BASE

Use this base to provide a convenient swivel option for this van seat. +$169.00

Use this base to provide a convenient swivel option for this van seat.">
94 DODGE SWIVEL BASE

This 1994 Dodge swivel base was designed to fit your aftermarket seat to your van with an 8x11” top bolt pattern, combined with a stock Dodge bottom hole bolt pattern that will bolt directly to the factory bolt holes on your floor, with no drilling required. For passenger seats.

▪Top Bolt Pattern 8x11”
▪Stock Dodge bottom bolt pattern
▪6” high at center
▪Seat bases tested and certified to meet FMVSS #207 safety standards per sections S4.2 and S4.3
112630
1995-99 DODGE DRIVER SWIVEL BASE

Use this base to provide a convenient swivel option for this van seat. +$169.00

Use this base to provide a convenient swivel option for this van seat.">
95-99 DODGE SWIVEL BASE

This 1995-99 Dodge swivel base was designed to fit your aftermarket seat to your van with an 8x11” top bolt pattern, combined with a stock Dodge bottom hole bolt pattern that will bolt directly to the factory bolt holes on your floor, with no drilling required.

▪Top Bolt Pattern 8x11”
▪Stock Dodge bottom bolt pattern
▪6” high at center
▪3" raised bottom plate
▪Seat bases tested and certified to meet FMVSS #207 safety standards per sections S4.2 and S4.3
112633
1995-99 DODGE PASSENGER SWIVEL BASE

Use this base to provide a convenient swivel option for this van seat. +$169.00

Use this base to provide a convenient swivel option for this van seat.">
95-99 DODGE SWIVEL BASE

This 1995-99 Dodge swivel base was designed to fit your aftermarket seat to your van with an 8x11” top bolt pattern, combined with a stock Dodge bottom hole bolt pattern that will bolt directly to the factory bolt holes on your floor, with no drilling required. For passenger seats.

▪Top Bolt Pattern 8x11”
▪Stock Dodge bottom bolt pattern
▪6” high at center
▪3" raised bottom plate
▪Seat bases tested and certified to meet FMVSS #207 safety standards per sections S4.2 and S4.3
112630
2000+ DODGE DRIVER SWIVEL BASE

Use this base to provide a convenient swivel option for this van seat. +$169.00

Use this base to provide a convenient swivel option for this van seat.">
2000+ DODGE SWIVEL BASE

This 2000+ Dodge swivel base was designed to fit your aftermarket seat to your van with an 8x11” top bolt pattern, combined with a stock Dodge bottom hole bolt pattern that will bolt directly to the factory bolt holes on your floor, with no drilling required.

▪Top Bolt Pattern 8x11”
▪Stock Dodge bottom bolt pattern
▪6” high at center
▪Seat bases tested and certified to meet FMVSS #207 safety standards per sections S4.2 and S4.3
112629
2000+ DODGE PASSENGER SWIVEL BASE

Use this base to provide a convenient swivel option for this van seat. +$169.00

Use this base to provide a convenient swivel option for this van seat.">
2000+ DODGE SWIVEL BASE

This 2000+ Dodge swivel base was designed to fit your aftermarket seat to your van with an 8x11” top bolt pattern, combined with a stock Dodge bottom hole bolt pattern that will bolt directly to the factory bolt holes on your floor, with no drilling required. For passenger seats.

▪Top Bolt Pattern 8x11”
▪Stock Dodge bottom bolt pattern
▪6” high at center
▪Seat bases tested and certified to meet FMVSS #207 safety standards per sections S4.2 and S4.3
112630
1994+ DODGE DRIVER POWER BASE RISER

This riser base is necessary when ordering a power base for your van. +$124.00

This riser base is necessary when ordering a power base for your van.">
1994+ DODGE POWER BASE RISER

The 1994+ Dodge power base riser was designed to match a power base to the original height of your seat. This power base riser features a universal bottom hole bolt pattern that will bolt directly to the factory bolt holes on your floor, with no drilling required.

▪Raises the power unit to match the original seat height
▪Universal bottom hole bolt pattern
▪Seat base risers tested and certified to meet FMVSS #207 safety standards per sections S4.2 and S4.3
111081
1994+ DODGE PASSENGER POWER BASE RISER

This riser base is necessary when ordering a power base for your van. +$124.00

This riser base is necessary when ordering a power base for your van.">
1994+ DODGE POWER BASE RISER

The 1994+ Dodge power base riser was designed to match a power base to the original height of your seat. This power base riser features a universal bottom hole bolt pattern that will bolt directly to the factory bolt holes on your floor, with no drilling required. For passenger seats.

▪Raises the power unit to match the original seat height
▪Universal bottom hole bolt pattern
▪Seat base risers tested and certified to meet FMVSS #207 safety standards per sections S4.2 and S4.3
111082

Your Price $396.90

Add to Wishlist

QUALITEX ZENITH HIGH BACK VAN SEAT

AVAILABLE IN FABRIC/VINYL/GENUINE LEATHER

Specifications

All high back van seats are custom made to specification
Heavy duty double tubing steel frame
Both seat armrests included in shipping, with the inside armrest already installed
7"slide tracks
Orthopedic foam lumbar support
No-sag suspension frame
Universal stop recline mechanism
Rear map pockets
All materials meet or exceed FMVSS #207 high back van seat safety standards, per sections S4.2 and S4.3

Product Description

The Zenith from Qualitex possesses another artistic, expressive two-tone design that can function in both subtle and bold ways. A clean, sleek exterior tone is matched by warm gathering folds in the interior tone, combining the best of both worlds into a singular eye-catching motif. Adjustable headrests increase this high back van seat’s convenient options, while gentle seat bolstering affords plenty of breathing space. No-sag suspension allows for level, even bottom support against rough terrain. With its outstanding look and upscale features, the Zenith is an obvious choice among high back van seats. Both seat armrests are included in shipping; the inside armrest already comes installed to the seat, for your convenience.

QTX-104-ZNT-VAN

California Residents: WARNING, Proposition 65 Notice

Use spaces to separate tags. Use single quotes (') for phrases.

Write Your Own Review

You're reviewing: Qualitex Zenith High Back Van Seat

How do you rate this product? *

	1 star	2 stars	3 stars	4 stars	5 stars
Quality
Price
Value

*Nickname
*Summary of Your Review
*Review
* This is a required field.